Ce1-XMnXO2-a复合氧化物催化剂甲烷催化燃烧性能的研究

采用水热法合成了系列Ce_1-XMn_XO_2-a-T(X=0.0，0.1，0.2，0.3，0.5，0.7，0.9，1.0；T表示焙烧温度)，T=500，650，800 ℃)复合氧化物催化剂用于甲烷的催化燃烧。通过XRD、N₂吸/脱附、TG-DSC、UV-Vis-DRS和TPR表征手段研究了不同组成催化剂的物理化学性质及其对甲烷催化燃烧活性。结果表明，在500 ℃焙烧的情况下Mn进入CeO₂晶格形成均相固溶体催化剂的最大取代值为0.7，而当Mn继续增加时则出现Mn₂O₃晶相偏析，同时各催化剂具有较高的比表面积；随着焙烧温度的升高，进入CeO₂晶格的Mn最大取代值逐渐减少，650和800 ℃时分别为0.5和0.3，且比表面积相应降低。Ce_1-XMn_XO_2-a-800催化剂的还原行为大致呈现三阶段，即为Mn₂O₃ → Mn₃O₄的还原(340～420 ℃)，Mn₃O₄ → MnO的还原(420～480 ℃)和体相氧化铈的还原(700～900 ℃)，且Mn的引入整体上提高了催化剂的可还原能力。甲烷催化燃烧活性评价结果表明，比表面积并非影响催化剂活性的主要因素，影响催化剂甲烷催化活性的主要因素为催化剂的组成、可还原能力和焙烧温度；而其中以Ce_0.3Mn_0.7O_2-a-800催化剂表现出较高的甲烷催化燃烧活性，在甲烷转化率为10%和90%时的温度分别为430 和613 ℃。进一步考察Ce_0.3Mn_0.7O_2-a在不同温度(500、650、800和1 000 ℃)焙烧后的催化活性表明，随着焙烧温度的提高催化剂催化活性降低。     

CexTi1-xO2复合氧化物的结构及负载CuO对NO还原性能研究

采用共沉淀法制备了不同摩尔比(x=0,0.1,0.2～0.9,1.0)的CexTi1-xO2复合氧化物,考察了CuO/CexTi1-xO2对NO+CO反应的活性,并用BET,TPR和XRD等技术对各试样进行了表征。结果表明,试样的结构和还原特性随焙烧温度变化而变化。XRD检测表明,x值从0.1增加到0.5时,650℃焙烧的试样已形成了CeTi2O6物相,且主要以无定形状态存在;试样经800℃焙烧后晶化完全;x>0.6时,一些TiO2已经进入了CeO2晶格,形成了Ce Ti固溶体。催化剂活性评价表明CuO/CexTi1-xO2(650℃)对NO+CO反应具有较好的活性,其活性随x值变化而变化。TPR及XRD结果表明CuO与CeTi2O6之间存在很强的相互作用,CeTi2O6物相的形成使CuO的还原峰温由380℃提前到200℃,而CuO的存在又促进CeTi2O6的还原峰温从600℃提前至200～300℃。     

Excess enthalpies of solution of some primary and secondary alcohols in sodium dodecylsulfate micellar solutions

The exces enthalpies of solution of some primary and secondary alcohols in aqueous sodium dodecylsulfate micellar solutions were measured and the results were explained by considering the distribution of alcohols between aqueous and micellar phases. The distribution constant and the enthalpy of transfer (and the standard free energy and entropy of transfer) were obtained. The thermodynamic parameters for the transfer of secondary alcohols from the aqueous to the sodium dodecylsulfate (NaDS) micellar phase differ slightly from those of the corresponding primary alcohols. For both series of alcohols the additivity rule holds for free energies of transfer whereas enthalpies and entropies display convex curves. The present data are compared to those for the transfer of the same solutes from the aqueous to the dodecyldimethylamine oxide (DDAO) and dodecyltrimethylammonium bromide (DTAB) micellar phases. The role of the hydrophilic interactions between the OH group and the micelles' head groups is formulated. The thermodynamics of the branched methyl group were determined. Furthermore, the thermodynamics of solvation of primary alcohols in water, in NaDS micelles, and in octane have been calculated using reference states based on the assumption that the empty space around alcohols in the initial and final states is the same. It is shown that the solvation of alcohols in NaDS micellar phase is enthalpy driven and that the thermodynamic properties of solvation vs. the length of the alcohol tail is the same for water and NaDS micelles whereas it is different for octane. A possible explanation for this difference is that the alkyl chain of alcohols folds in octane.     

The BKK root count in

The root count developed by Bernshtein, Kushnirenko and Khovanskii only counts the number of isolated zeros of a polynomial system in the algebraic torus . In this paper, we modify this bound slightly so that it counts the number of isolated zeros in . Our bound is, apparently, significantly sharper than the recent root counts found by Rojas and in many cases easier to compute. As a consequence of our result, the Huber-Sturmfels homotopy for finding all the isolated zeros of a polynomial system in can be slightly modified to obtain all the isolated zeros in .

     

Synthesis and performance of HPTLC plates modified with cyanopropyl- and octadecyl-trichlorosilane

Chemical modification of commercial high performance thin-layer chromatography plates with various mixtures of cyano-propyltrichlorosilane and octadecyltrichlorosilane is described. Surface coverage by different treatments is demonstrated as well as the variations in chromatographic performance. With regard to the development in aqueous media the utility of CN/ ODS plates compared to ODS plates is also shown.     

Characterization of OV-1/FFAP-mixture coated glass capillary columns used for the separation of free fatty acids

As an alternative to acid pretreated UCON and FFAP capillaries for the analysis of wide-boiling free fatty acid mixtures, OV-1 : FFAP phase mixtures were used on high-temperature silylated inert glass capillary columns. The HETP-carrier gas velocity curves, peak asymmetry factors, coating efficiency, gas phase and stationary phase contributions to the mass transfer resistance were determined for various OV-1 : FFAP ratios. Mixed-phase capillaries showed optimum performance at a 2 : 1 OV-1 : FFAP ratio. The thermal and long-term stability of OV-1-stabilized FFAP columns surpassed those of the UCON and pure FFAP reference column used.     

Ionization constants for deuterium oxide in deuterium oxide-organic mixtures

A potentiometric method using a glass electrode has been applied to determination of ionization constants for deuterium oxide (D₂O) in binary mixtures of D₂O with dioxane, tetrahydrofuran, acetone, dimethylsulfoxide, CH₃CH₂OD, and CH₃OD at 25°C. The results are compared with values of ionization constants for H₂O obtained previously in the corresponding H₂O-organic mixtures, and the isotope effect is shown to be small. Further calculations with the D₂O results show that the first five solvents mentioned above are neither appreciably acidic nor basic in D₂O solution, but that CH₃OD shows slightly acidic behavior (pK_a=16.0±0.3).     

Calcined Ni—Al layered double hydroxide as a catalyst for total oxidation of volatile organic compounds: Effect of precursor crystallinity

The effect of hydrothermal treatment on properties (crystallinity, porous structure, reducibility, acidity, basicity, and catalytic activity and selectivity in toluene and ethanol total oxidation) of Ni—Al layered double hydroxide precursors and related mixed oxides was examined. The hydrothermal treatment increased considerably both the content of crystalline phase and LDH crystallite size. On the other hand, only a slight effect of the precursor hydrothermal treatment on crystallinity of the related Ni—Al mixed oxides obtained by calcination at 450°C was observed. The reducibility of NiO particles appeared to be hindered considerably compared to the reducibility of pure NiO. Catalytic activity of the Ni—Al mixed oxides prepared from the precursors hydrothermally treated for a short time (4 h) was the highest. The highest amount of acetaldehyde formed during the total oxidation of ethanol, i.e. the worst selectivity was found for the calcined Ni—Al LDH without hydrothermal treatment. Presented at the 33rd International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 22–26 May 2006.     

药用缓释辅料——羟丙基甲基纤维素的合成及其缓释性能的研究

本文研究了药物缓释材料HPMC的合成方法,探讨了碱纤维素制备,醚化剂浓度,混合醚化剂配经以及产品后处理对高粘度HPMC的影响。本文还初步对KCl,氨茶碱,硝酸异山梨醇酯等药物采用合成的HPMC作辅料,进行了缓释制剂的研究,结果表明合成的HPMC具有满意的缓释性能。     

Kinetics of the thermal dehydrations and decompositions of some mixed metal oxalates

Both isothermal and programmed temperature experiments have been used to obtain kinetic parameters for the dehydrations and the decompositions in nitrogen of the mixed metal oxalates: FeCu(ox)₂·3H₂O, CoCu(ox)₂·3H₂O and NiCu(ox)₂·3.5H₂O, [ox=C₂O₄]. Results are compared with those reported for the thermal decompositions of the individual metal oxalates, Cuox, Coox·2H₂O, Niox·2H₂O and Feox·2H₂O. X-ray photoelectron spectroscopy (XPS) was also used to examinee the individual and the mixed oxalates. Dehydrations of the mixed oxalates were mainly deceleratory processes with activation energies (80 to 90 kJ·mol⁻¹), similar to those reported for the individual hydrated oxalates. Temperature ranges for dehydration were broadly similar for all the hydrates studied here (130 to 180°C). Decompositions of the mixed oxalates were all complex endothermic processes with no obvious resemblance to the exothermic reaction of Cuox, or the reactions of physical mixtures of the corresponding individual oxalates. The order of decreasing stability, as indicated by the temperature ranges giving comparable decomposition rates, was NiCu(ox)₂>CoCu(ox)₂>FeCu(ox)₂, which also corresponds to the order of increasing covalency of the Cu−O bonds as shown by XPS. In celebration of the 60^th birthday of Dr. Andrew K. Galwey